Grahame N's Web Pages


THE 9.5MM PATHÉSCOPE
IMP CINE PROJECTOR

from Grahame L. Newnham B.Sc.


The little 'Pathéscope Imp' 9.5mm cine projector was first announced in the December 1934 edition of the Pathéscope 'house magazine' - the Pathéscope Monthly, Just in time for Christmas! An upgrade to the earlier 'Kid' 9.5mm cine projector which had been around since the early 1930s as a cheaper alternative to the original 'Pathé-Baby' or 'Home Movie' 9.5mm silent projector.


Pathéscope Monthly magazine December 1934


Pathéscope Monthly magazine December 1934

Of similar presssed steel construction as the 'Kid', finished in a high-gloss black enamel, the 'Pathéscope Imp' had a number of improvements which rather influenced the name of the little projector -' IMP-roved'. The film gate hinged back for easy threading and mainly for cleaning. (The 'Kid' had been well known for scratching the film because of accumulated dirt in the gate which was virtually inaccessible for cleaning!). In addition the 'Imp' had been designed for use with a motor attachment having a drive shaft with a small pulley/flywheel for the motor drive. There was also a simple 'super-attachment' that enabled the use of film spools up to 300 foot / 100 metre size. (The 'super-attachment' also fitted the discontinued 'Kid' projector). This machine was also designed to operate stills with the 'notched title' films.



Pathéscope 1935 & 1936 catalogues


Pathéscope 1935 & 1936 catalogues



Pathéscope 1935 & 1936 catalogues

The 'Pathéscope Imp' used a similar compact optical system as the previous 'Kid' model, and the small tubular lamp with the Pathé 'T' piece fitting as used in the original 'Pathé-Baby/Home-Movie' and 'Kid' projectors. The standard lamp supplied was the 12 volt 0.5amp 6 watt version - ref. no. B.P.109. This was supplied from the mains via a dropper resistance housed in a metal case. A later "C" type, 20 volt (10watt) lamp offered a little more illumination. These lamps were all 0.5 amp current rating hence could still operate from the same dropper resistance, Just to complicate matters, a brighter lamp - "D" type, 20 volts 20watts was also offered later, but this needed an upgraded dropper resistance - Pathéscope did a 'trade-in' offer to allow owners to swop their dropper resistances for a small fee.

This variation of lamp voltages and currents must havre caused many lamp failures amid the confusion and no doubt havoc for the dealers! A transformer would possibly have been a better idea, but at that time parts of the UK still had D.C. (Direct Current() mains supplies which could only work with dropper resistances. In fact some houses still had no mains electricity, hence the mention of accumulators to supply the lamps! (Luckily I seem to have grown up with A.C. mains which enabled me to experimemt with all manner of deadly wires, switches, lamps etc. from an early age; although an old lady down the street still had gas lighting!)

It looks quite straightforward to fit modern QI halogen G4 base lamps like the little 6volt 10watt M29 often used in the 'Pathé-Baby' lamp conversions. Just remember that anything above 10 watts will begin to ruin the single frames on the early 'notched' 9.5mm film prints, However there are now LED 'imitations' of this type of lamp - I am waiting to try some......



Pathéscope Imp 9.5mm cine projector - operating side
(my example has motor & super-attachment fitted )


Pathéscope Imp 9.5mm cine projector - non-operating side
(the black dropper resistance box is often useful for housing updated lamp & motor power supplies)



Pathéscope Imp 9.5mm cine projector - showing the easy opening film gate



Pathéscope Imp nameplate - note the 'Made In England'!



Threading film in the 'Pathéscope Imp' cine projector
(from the Harold Abbott book - 'The Complete 9.5mm Cinematographer')



The Pathéscope 1935 catalogue offered a few 'Imp' accessories

By 1935, Pathéscope had added a leatherette covered sturdy carry case for the 'Imp' projector to their sales lists - it cost only 15sh (75p) and had space for projector, motor, super attachment, mains dropper resistance, mains cable, films and spools. There was also a brake-arm which helped to prevent 'overrun' with the new 200 foot / 60 metre 'M' reels.



Pathescope Imp drive motor

The 'Pathéscope Imp' drive motor was also made in England. It runs on 110 volts, but I have been experimenting with a room light dimmer switch which seems to work fine with this motor. My dimmer switch turns for on/off then brightness increase. This is just right for this motor - just don't turn the switch up too much!!



Pathéscope Imp lamphouse - seems OK for the M29 6 volt 10 watt QI lamp conversion, but not much cooling!



Pathéscope Imp 'innards' - single barrel shutter at the top, don't forget lubrication sometimes!


Notes:

1. The 'Imp' was British made, possibly at the Manchester works of the Salford Electrical Instrument Company. Maybe the optical parts, lens, condenser and reflector (similar to those on the 'Pathé-Baby' and 'Kid') still came from France.

2. Production of the 'Imp' ceased in 1937. By 1938, the little'Ace' had replaced the 'Imp' as the cheapest 9.5mm projector. At only 37/6d it was far, far cheaper than the 'Imp' had been at over £4. Accessories continued to be available for the 'Imp' - the motor, carry case, super-attachment and brake-arm extension set (some also suitable for the 'Pathé-Baby' and 'Kid'. Notched titles were no more, the new little 'Ace' did not have a notched title device.

3. Whilst the 'Kid' projector began life in France, I can find no mention of the 'Imp' being marketed over there.

4. The lens diameter is just 14mm, fitted with a small pin which engages in a slot to aid focussing. Rather too small to use other lenses!

5. The little bakelite 'Ace' lens will fit the 'Imp' just fine. (Probably the same bits of glass inside!)

6. The 'Imp' motor brushes are 4mm square, I do have them on my sales lists!

7. I also have new 'Imp' motor drive belts, spring take-up belts and instruction booklet reprints on my sales lists! (gln Jun2018)

8. Some 'Imp' typical serial numbers:- ZA21740 - (stamped inside the base)


Return to: 9.5 PATHE EQUIPMENT ................or return to MAIN MENU


New 21Jun2018 ............. Last updated: 10 December 2019 .............. 95gearpatheimp.htm .......... ©MMXV111 Grahame .L. Newnham